Newest Products
E53-E54 Register and Octave Tube Removers
E53 Register and E54 Octave Tube Removers Used to remove octave tubes before polishing the bore. E53 Clarinet Register Remover E54 Oboe Octave Tube Remover
E55 Thumb Tube Remover
This thumb tube remover tool is designed to remove and install threaded or pressed in tubes on many soprano clarinets. It will not scratch or mar the inside of the...
E56 Wax Spoon
Special wax spoon made of copper to hold heat. Used to place wax around reeds.
E57A Small Post Body Countersink
Makes a flat seat when replacing post in graft or replacing with larger threads. Knurled for hand operation. Also adjusts seats so posts can be lined up. E57A: .226 D...
E58 Sax Key Swedging Dies
E58 Sax Key Swedging Dies Usually used on top stack C, bis Bb, bottom stack F# and old style middle finger fork Eb mechanism lever. Available: E58A Small E58B Regular
E59 Pearl Protector
Used to place over the pearl while heating sax pads. Prevents scorching of pearls
E60 Crack Slick Spatula
A brass iron, flat on one side, curved on the other. Used for smoothing Shellac into woodwind cracks or other spreading uses.
E61 Flute Gauge
Special gauge for adjusting flute pad cup openings and for leveling. The small step is for trills and the upper C# key. The middle step is for mainline keys on...
E62-E66 Replacement Belts For Z2
Belts measure 1" (25.4mm) wide x 42" (1.07mm) long. 80 - 120 - 150 - 240 - 320 Grit
E67 Post Locking Screw Countersink
The E67 Post Locking Screw Countersink is used to drill and countersink the proper size hole when installing a post locking screw. The countersink duplicates the taper on the bottom...
E68 Post Body 5.8mm Countersink and Drill
E68 (5.8mm) & E69 (6.5mm) POST BODY COUNTERSINKS These two post body countersinks and thread pilot drills are used to countersink the post flange into the instrument body after a...
E69 Post Body 6.5mm Countersink and Drill
E69 (6.5mm) & E68 (5.8mm) POST BODY COUNTERSINKS These two post body countersinks and thread pilot drills are used to countersink the post flange into the instrument body after a...
E7 Tapered Spindles
E7 Tapered Spindles Mount on motor shaft for scratch brush or small buffs. Fit over motor shaft affixed by set screw. Comes in two sizes, in both right and left...
E70 Cork Protector
Used to place over the end of a sax neck during the installation of a neck cork using shellac. Will prevent burning of the cork while heating the tube.
E71 Key Filing Clamp
Preferred by some technicians to hold parts during filing, polishing or general work. Made of hard wood with two leather lined jaws...one round and one square. When the tapered wedge...
E8 & E8A Saxophone Neck Holder
E8 Saxophone Neck Holder Two expandable mandrels to spin a sax neck in a lathe while sanding corks. Do not use in a Bench Motor. Insert in lathe chuck or...
E81-E85 Tone Hole Pad Seat Files
Perfectly ground, razor sharp edges, negative rake to prevent gouging. Use to remove small chips from tone holes of wood, rubber and plastic clarinets. E81 1/4 (6.4mm) Tone Hole Pad...
E87 Mini Tone Hole File
E87 Mini Tone Hole File (Especially for piccolo) E87A 1/4 (6.4mm) Mini Tone Hole File E87B 3/8 (9.5mm) Mini Tone Hole File E87C 17/32 (13.5mm) Mini Tone Hole File
E9 Large Flute Pad Ironing Tool
The E9 Flute Pad Ironing Tool is made of tempered stainless steel. It has two center holes of different diameters, both larger than our E34 Flute Pad Ironing Tool. Used...